STEP 1: Drag and drop the components in the workspace to create the circuit.

Nos of required components:

AC Source – 1, Thyristor - 1, Gate Pulse - 1, Resistor - 1

Ammeter - 1, Voltmeter – 4, Ground – 1


STEP 2: Make the connections as per the instructions given below:

(a) (01-05, 03-05, 08-05, 09-06)

(b) (02-17, 04-17, 07-10)

(c) (10-11, 12-13, 06-14)

(d) (06-18, 15-16, 17-19)

Note: Click on the wire to delete the connection.

STEP 3: Click on the CHECK button to check the connections.

Note: Right click on the component to open the dialog box to edit the properties of the component.

STEP 4: Input the values for all the required components (AC Source, Gate Pulse and Resistor) and the waveform will get plot automatically.

STEP 5: Now, Click on the ADD button to insert the reading into the observation table.

STEP 6: Now, you can input different values as per your requirement to get the desired waveform.

STEP 7: Repeat Step 5 to again insert the reading into the table and now repeat Steps 6 to 7 to take more readings.

STEP 8: Click on the PRINT button to take out the print of the webpage.

STEP 9: Click on the RESET button to reload the webpage.

STEP 1: Drag and drop the components in the workspace to create the circuit.

Nos of required components:

AC Source – 1, Thyristor - 1, Gate Pulse - 1, Resistor - 1

Inductor - 1, Ammeter - 1, Voltmeter – 4, Ground – 1


STEP 2: Make the connections as per the instructions given below:

(a) (01-05, 03-05, 08-05, 09-06)

(b) (02-21, 04-21, 07-10, 10-11)

(c) (12-13, 06-14, 15-16)

(d) (15-18, 17-20, 19-21)

Note: Click on the wire to delete the connection.

STEP 3: Click on the CHECK button to check the connections.

Note: Right click on the component to open the dialog box to edit the properties of the component.

STEP 4: Input the values for all the required components (AC Source, Gate Pulse, Resistor and Inductor) and the waveform will get plot automatically.

STEP 5: Now, Click on the ADD button to insert the reading into the observation table.

STEP 6: Now, you can input different values as per your requirement to get the desired waveform.

STEP 7: Repeat Step 5 to again insert the reading into the table and now repeat Steps 6 to 7 to take more readings.

STEP 8: Click on the PRINT button to take out the print of the webpage.

STEP 9: Click on the RESET button to reload the webpage.

STEP 1: Drag and drop the components in the workspace to create the circuit.

Nos of required components:

AC Source – 1, Thyristor - 1, Gate Pulse - 1, Resistor - 1, Inductor - 1

DC Source - 1, Ammeter - 1, Voltmeter – 5, Ground – 1


STEP 2: Make the connections as per the instructions given below:

(a) (01-05, 03-05, 08-05, 09-06, 02-23)

(b) (04-23, 07-10, 10-11, 12-13)

(c) (06-14, 15-16, 15-18, 17-20)

(d) (21-22, 22-24, 19-23, 23-25)

Note: Click on the wire to delete the connection.

STEP 3: Click on the CHECK button to check the connections.

Note: Right click on the component to open the dialog box to edit the properties of the component.

STEP 4: Input the values for all the required components (AC Source, Gate Pulse, Resistor, Inductor and DC Source) and the waveform will get plot automatically.

STEP 5: Now, Click on the ADD button to insert the reading into the observation table.

STEP 6: Now, you can input different values as per your requirement to get the desired waveform.

STEP 7: Repeat Step 5 to again insert the reading into the table and now repeat Steps 6 to 7 to take more readings.

STEP 8: Click on the PRINT button to take out the print of the webpage.

STEP 9: Click on the RESET button to reload the webpage.