STEP 1: Drag and drop the components in the workspace to create the circuit.

Nos of required components:

AC Source – 1, Thyristor – 4, Gate Pulse – 4, Resistor - 1

Ammeter – 1, Voltmeter – 8, Ground - 2


STEP 2: Make the connections as per the instructions given below:

(a) (01-03, 03-08, 02-04, 08-24, 14-30)

(b) (04-30, 05-07, 06-08, 07-17, 13-17)

(c) (18-37, 09-10, 11-13, 12-14, 15-16)

(d) (10-19, 20-21, 22-24, 23-25, 26-27)

(e) (27-35, 34-36, 28-30, 29-31, 32-33)

(f) (25-31, 31-38, 37-39, 38-40)

Note: Click on the wire to delete the connection.

STEP 3: Click on the CHECK button to check the connections.

Note: Right click on the component to open the dialog box to edit the properties of the component.

STEP 4: Input the values for all the required components (AC Source, Gate Pulses and Resistor) and the waveform will get plot automatically.

STEP 5: Now, Click on the ADD button to insert the reading into the observation table.

STEP 6: Now, you can input different values as per your requirement to get the desired waveform.

STEP 7: Repeat Step 5 to again insert the reading into the table and now repeat Steps 6 to 7 to take more readings.

STEP 8: Click on the PRINT button to take out the print of the webpage.

STEP 9: Click on the RESET button to reload the webpage.

STEP 1: Drag and drop the components in the workspace to create the circuit.

Nos of required components:

AC Source – 1, Thyristor – 4, Gate Pulse – 4, Resistor - 1

Inductor - 1, Ammeter – 1, Voltmeter – 8, Ground - 2


STEP 2: Make the connections as per the instructions given below:

(a) (01-03, 03-08, 02-04, 08-24, 14-30)

(b) (04-30, 05-07, 06-08, 07-17, 13-17)

(c) (18-37, 09-10, 11-13, 12-14, 15-16)

(d) (10-19, 20-21, 22-24, 23-25, 26-27)

(e) (27-35, 34-36, 28-30, 29-31, 32-33)

(f) (25-31, 31-40, 38-39, 37-41, 40-42)

Note: Click on the wire to delete the connection.

STEP 3: Click on the CHECK button to check the connections.

Note: Right click on the component to open the dialog box to edit the properties of the component.

STEP 4: Input the values for all the required components (AC Source, Gate Pulses, Resistor and Inductor) and the waveform will get plot automatically.

STEP 5: Now, Click on the ADD button to insert the reading into the observation table.

STEP 6: Now, you can input different values as per your requirement to get the desired waveform.

STEP 7: Repeat Step 5 to again insert the reading into the table and now repeat Steps 6 to 7 to take more readings.

STEP 8: Click on the PRINT button to take out the print of the webpage.

STEP 9: Click on the RESET button to reload the webpage.

STEP 1: Drag and drop the components in the workspace to create the circuit.

Nos of required components:

AC Source – 1, Thyristor – 4, Gate Pulse – 4, Resistor - 1, Inductor - 1

DC Source - 1, Ammeter - 1, Voltmeter – 9, Ground - 2


STEP 2: Make the connections as per the instructions given below:

(a) (01-03, 03-08, 02-04, 08-24, 14-30)

(b) (04-30, 05-07, 06-08, 07-17, 13-17)

(c) (18-37, 09-10, 11-13, 12-14, 15-16)

(d) (10-19, 20-21, 22-24, 23-25, 26-27)

(e) (27-35, 34-36, 28-30, 29-31, 32-33)

(f) (25-31, 38-39, 40-41, 31-42, 41-43)

(g) (42-44, 37-45, 42-46)

Note: Click on the wire to delete the connection.

STEP 3: Click on the CHECK button to check the connections.

Note: Right click on the component to open the dialog box to edit the properties of the component.

STEP 4: Input the values for all the required components (AC Source, Gate Pulses, Resistor, Inductor and DC Source) and the waveform will get plot automatically.

STEP 5: Now, Click on the ADD button to insert the reading into the observation table.

STEP 6: Now, you can input different values as per your requirement to get the desired waveform.

STEP 7: Repeat Step 5 to again insert the reading into the table and now repeat Steps 6 to 7 to take more readings.

STEP 8: Click on the PRINT button to take out the print of the webpage.

STEP 9: Click on the RESET button to reload the webpage.