Single Phase Full Wave Mid-point Converter with R Load and RL Load
Single Phase Full Wave Mid-Point Converter with R Load
STEP 1: Drag and drop the components in the workspace to create the circuit.
No. of required components:
AC Source – 1, 3-W Transformer - 1, Thyristor - 2, Gate Pulse - 2,
Resistor - 1, Ammeter - 1, Voltmeter – 6, Ground – 2
STEP 2: Make the connections as per the instructions given below:
(a) (01-03, 02-04, 03-05, 04-06, 07-12)
(b) (10-12, 11-13, 13-22, 14-15, 15-16)
(c) (17-18, 08-19, 20-21, 19-23)
(d) (20-24, 09-27, 25-27, 26-28)
(e) (29-30, 30-31, 32-33, 22-28)
Note: Click on the wire to delete the connection.
STEP 3: Click on the CHECK button to check the connections.
Note: Right click on the component to open the dialog box to edit the properties of the component.
STEP 4: Input the values for all the required components (AC Source, Gate Pulses and Resistor) and the waveform will get plot automatically.
STEP 5: Now, Click on the ADD button to insert the reading into the observation table.
STEP 6: Now, you can input different values as per your requirement to get the desired waveform.
STEP 7: Repeat Step 5 to again insert the reading into the table and now repeat Steps 6 to 7 to take more readings.
STEP 8: Click on the PRINT button to take out the print of the webpage.
STEP 9: Click on the RESET button to reload the webpage.
No. of required components:
AC Source – 1, 3-W Transformer - 1, Thyristor - 2, Gate Pulse - 2,
Resistor - 1, Ammeter - 1, Voltmeter – 6, Ground – 2
STEP 2: Make the connections as per the instructions given below:
(a) (01-03, 02-04, 03-05, 04-06, 07-12)
(b) (10-12, 11-13, 13-22, 14-15, 15-16)
(c) (17-18, 08-19, 20-21, 19-23)
(d) (20-24, 09-27, 25-27, 26-28)
(e) (29-30, 30-31, 32-33, 22-28)
Note: Click on the wire to delete the connection.
STEP 3: Click on the CHECK button to check the connections.
Note: Right click on the component to open the dialog box to edit the properties of the component.
STEP 4: Input the values for all the required components (AC Source, Gate Pulses and Resistor) and the waveform will get plot automatically.
STEP 5: Now, Click on the ADD button to insert the reading into the observation table.
STEP 6: Now, you can input different values as per your requirement to get the desired waveform.
STEP 7: Repeat Step 5 to again insert the reading into the table and now repeat Steps 6 to 7 to take more readings.
STEP 8: Click on the PRINT button to take out the print of the webpage.
STEP 9: Click on the RESET button to reload the webpage.
Single Phase Full Wave Mid-Point Converter with RL Load
STEP 1: Drag and drop the components in the workspace to create the circuit.
No. of required components:
AC Source – 1, 3-W Transformer - 1, Thyristor - 2, Gate Pulse - 2,
Resistor - 1, Inductor - 1, Ammeter - 1, Voltmeter – 6, Ground – 2
STEP 2: Make the connections as per the instructions given below:
(a) (01-03, 02-04, 03-05, 04-06, 07-12)
(b) (10-12, 11-13, 13-24, 14-15, 15-16)
(c) (17-18, 08-19, 20-21, 22-23, 19-25)
(d) (22-26, 09-29, 27-29, 28-30, 24-30)
(e) (22-26, 09-29, 27-29, 28-30, 24-30)
(f) (31-32, 32-33, 34-35)
Note: Click on the wire to delete the connection.
STEP 3: Click on the CHECK button to check the connections.
Note: Right click on the component to open the dialog box to edit the properties of the component.
STEP 4: Input the values for all the required components (AC Source, Gate Pulses, Resistor and Inductor) and the waveform will get plot automatically.
STEP 5: Now, Click on the ADD button to insert the reading into the observation table.
STEP 6: Now, you can input different values as per your requirement to get the desired waveform.
STEP 7: Repeat Step 5 to again insert the reading into the table and now repeat Steps 6 to 7 to take more readings.
STEP 8: Click on the PRINT button to take out the print of the webpage.
STEP 9: Click on the RESET button to reload the webpage.
No. of required components:
AC Source – 1, 3-W Transformer - 1, Thyristor - 2, Gate Pulse - 2,
Resistor - 1, Inductor - 1, Ammeter - 1, Voltmeter – 6, Ground – 2
STEP 2: Make the connections as per the instructions given below:
(a) (01-03, 02-04, 03-05, 04-06, 07-12)
(b) (10-12, 11-13, 13-24, 14-15, 15-16)
(c) (17-18, 08-19, 20-21, 22-23, 19-25)
(d) (22-26, 09-29, 27-29, 28-30, 24-30)
(e) (22-26, 09-29, 27-29, 28-30, 24-30)
(f) (31-32, 32-33, 34-35)
Note: Click on the wire to delete the connection.
STEP 3: Click on the CHECK button to check the connections.
Note: Right click on the component to open the dialog box to edit the properties of the component.
STEP 4: Input the values for all the required components (AC Source, Gate Pulses, Resistor and Inductor) and the waveform will get plot automatically.
STEP 5: Now, Click on the ADD button to insert the reading into the observation table.
STEP 6: Now, you can input different values as per your requirement to get the desired waveform.
STEP 7: Repeat Step 5 to again insert the reading into the table and now repeat Steps 6 to 7 to take more readings.
STEP 8: Click on the PRINT button to take out the print of the webpage.
STEP 9: Click on the RESET button to reload the webpage.